Hatcher Gun Company LLC

"Where Pride and Excellence is the Standard"

Home ] Up ] Apparel ] Contact HGC ] About ] Search ]



Gunsmithing Links

Back To Gunsmithing      Pistolsmithing     Riflesmithing     Shotgunsmithing


Shotgunsmithing

General Work

Description

Price

Minimum Charge Per Job - (Unless stated otherwise) $60.00
Clean & Oil Shotgun - (Completely DisAssy. & check for wear) $60.00
Pattern Shotgun - (Doesn't include ammo or targets) $100.00
Long Forcing Cone - (Non-Plated Bore, Per Barrel)

$80.00

Long Forcing Cone - (Plated Bore, Per Barrel) $125.00
Resolder Rib $60/Hr.
Raise Dent in Barrel $100.00
Raise Dented Rib $60.00
Straighten / Adjust Barrel $200.00
Polish Chamber / Bore $80.00
Back Boring - (Non-Plated Bores) $60/Hr.
Open/Modify Choke $100.00
Remove Stuck Choke Tube $50.00
Install Screw-In Choke - (Winchoke/Truechoke/Remchoke Non-Plated Bores) $175.00
Drill & Tap for Front or Mid Rib Bead $40.00
Check Firing Pin Protrusion $20.00
Make Chamber Cast $50.00
Remove Fouling From Bore $50.00

Metal Finishing

Bluing

Bluing consists of Disassembly, Cleaning, Removing old blue and rust, Polishing, Bluing, Oiling, and Reassembling of gun.

Description

Price

Matte Finish - Soft or Heavy (Polish out Pitting with 140 polish, Bead Blast) $175.00
Standard Finish - (Polish out Pitting, Finish with 140 polish) $175.00
Deluxe Finish - (As above followed with 240 & 400  polish) $215.00
Master Finish - (As above followed with 500 & 555 polish to a mirror finish) $300.00
Parkerizing - (Polish out Pitting, Finish with 140 & Bead Blast $175.00
Cerakote Heat and Dura-Coat $180.00

Other Finishing

Hard Chrome POR
Case Coloring - (Price depending on number of pieces) POR
Draw Filing Hr./Rate
Jewel Bolt Hr./Rate
Jewel Carrier Hr./Rate
Stock Work
 

Stock Finishes include stripping the old finish, sanding to 400 grit, raising the grain between grits, and sealing the stock.

Description

Price

Standard Stock Finish - (Unfilled oil, Satin) $200.00
Deluxe Stock Finnish - (Filled, Hand Rubbed Oil in Satin or Gloss) $300.00
Spray Lacquer or Polyurethane- (Gloss) $300.00
Black Wrinkle Paint Finish $200.00
Inletting Semi-Finished Stock $200.00
Install Recoil Pad $50.00
Install Adj. Butt Plate $150.00
Install Adj. Comb Hardware $225.00
Install Recoil Reducer - (In Butt Stock) $70.00
Install Sling Swivel Stud - (Butt Stock) $30.00
Recut Checkering - (Per Panel) (By the Hour, Priced by complexity of pattern) POR
Checkering - (By the Hour, Priced by complexity of pattern) POR

Because of unforeseen complications, many prices could be higher than those shown.

Base Prices as of 1/01/13

Prices subject to change without notice.

Send mail to: admin@hatchergun.com with questions or comments about this site.   

Copyright 2015 Hatcher Gun Company LLC.

Address: 76650 Rd. 342 Elsie, NE. 69134

Phone: 308-228-2454

Last modified 04/26/17